Search Results

THIS PAPER outlines progress to October, 1958, on the new Shock and Vibration Manual. At that point, the methods of solving vibration isolation problems had been established. After further refinements and expansion, the manual will be issued by SAE Committee S-12 on Shock and Vibration. The manual will set up procedures to be followed by engineers who don't have extensive experience in the field. It will give procedures for problems having up to six degrees of freedom. The procedure, as described in the paper, now consists of three steps: 1. Specification of the data required for the solution of a given problem. 2. Calculating whether vibration isolators are needed. 3. Determining the dynamic properties of the isolation system when the above step indicates isolation mounts are needed.

The paper summarizes the experience gained on the ISS water management system during the missions of ISS-1 through ISS-16 (since November 2 2000, through December 31, 2007). The water supply sources and structure, consumption and supply balance at various phases of space station operation are reviewed. The performance data of the system for water recovery from humidity condensate SRV-K and urine feed and pretreatment system SPK-U in the Russian orbital segment are presented. The key role of water recovery on a board the ISS and the need to supplement the station's water supply hardware with a system for water reclamation from urine, water from a carbon dioxide reduction system and hygiene water is shown.

THIS PAPER reviews VTOL problems, indicating probable ways toward optimization of whole lifting and propelling system. Also discussed are the power and thrust requirements for optimum cruise and vertical take-offs and landings for propeller-driven and jet-propelled aircraft. Three speed ranges offer the most promise for VTOL aircraft, if thrust requirements for cruise and take-off are to match. The ranges are centered around Mach numbers of 0.65, 0.8, and 2.0+. There is a possibility of overcoming the high thrust needed for hovering by use of bypass augmentation, special hovering jets, or favorable ground effects, the author reports.

HEAT TRANSFER causes loading and starting design problems in large missile systems powered by cryogenic propellants. This manifests itself during loading as effective density variation, violent surface conditions, boiloff, and ice formation — problems which may be solved by insulating the tank. During starting it causes overheating and caviation — effects which may be reduced by recirculators and subcooled charge injections. The study described in this paper centers around liquid oxygen and its variations in heat flux rate, which affect liquid density, surface condition, and replenishing requirements. The problem areas are made apparent by consideration of a hypothetical missile system.*

THE optimum mode of control for an aircraft engine is dependent on both the configuration of the engine and its application. Each engine application requires several detail modes of control, one for each definable regime of operation of the engine. Discussions of control requirements can be simplified by classifying these regimes by objectives: physical limiting, thrust, and transient control. The turbojet engine is the basis for the discussion in this paper. Acceptable modes of control can often be selected by inspection of the engine and its application. Selection of an “optimum” control mode requires investigation of the operation of the engine and weapons system at every stage of its use. The selection of a “mode” of control requires a compromise between performance and other design factors. The need for simplicity and accuracy must be balanced against the stability requirements. The availability and flexibility of control components may limit the modes of control considered.

IF ROCKET OR MISSILE designers were asked to choose one specific property of engineering materials they would like to have improved, the largest percentage would undoubtedly select strength at high temperature. In addition to retaining strength at high temperatures, missile materials must be resistant to erosion and ablation. Missile structures must also be satisfactory when subjected to aerodynamic and acceleration loads, high stresses of vibration, and thermal shock. The need for low-density, easily fabricated, heat-resistant materials has resulted in a continuing search for more effective combinations of known materials, as well as the development of new materials. This paper discusses some interesting results obtained in studies of composite materials that might be used for rocket or missile construction.

STRUCTURAL MATERIALS for Mach 3 jet transports pose difficult problems for the design engineer. Reasons for this problem are the incomplete information available on the many possible metals and the diversity of critical properties that are added by supersonic requirements. The material properties discussed in this paper include tensile strength, resistance to crack propagation, ease of fabrication, weldability, and thermal expansion. Cost factors are also considered. The structural configuration of the wing and fuselage is an example of the complexity of the material selection problem. The wing may be rigidity-critical, and the fuselage strength-critical; each requires diferent material properties to solve the problem.*

NEW WELDING processes are dropping costs while providing improvements in weld quality. This paper describes some of the more promising new developments in pressure and fusion welding and brazing. Included in the discussion are ultrasonic, high frequency resistance, foil seam, magnetic force, percussion, friction, and thermopressure welding and diffusion bonding. The description of adhesive bonding includes the development of glass or ceramic materials as structural adhesives.*

Mobility is in the midst of an electric revolution, propelled by industry innovators such as magniX. Headquartered in Redmond, Washington, the magniX team is focused on revolutionizing electric motors for commercial aviation applications.

Most emerging electric vertical takeoff and landing (eVTOL) aircraft feature distributed electric propulsion systems with automation features that simplify operations for future pilots. In theory, increasing automation levels should reduce pilot workload, decrease training time, and improve performance consistency. Air Education and Training Command Detachment 62 (AETC/Det 62) sought to test this theory as part of a larger study involving 70+ participants, two eVTOL platform simulators, and multimodal assessments of flight performance. In the present report, we compared expert ratings of flight performance of pilots who do not have prior pilot experience or training (herein referred to as ab initio pilots; i.e., 0 flight hours) to those of experienced pilots (i.e., >300 flight hours) in either a semi-automated or highly-automated simulated eVTOL platform.

THIS PAPER presents the development of the DC-8 suppressor and thrust brake unit from initial test work through the final design. The selection of the production unit was based on a wide background of test work using both model and full-scale facilities. On the basis of this work, the configuration selected for production consisted of a fixed, corrugated, suppressing nozzle with a retractable ejector. A target-type thrust brake, mounted in the ejector, was chosen for the thrust brake production unit. Approximately 12-db suppression and 44% reverse thrust are provided by the unit. The ejector is hydraulically operated and the thrust brake air actuated. Both actuation systems obtain power from the aircraft systems which provides for operation during engine-out conditions. Alternate methods of actuation are provided in case of a primary system failure.

THIS PAPER is concerned with design problems which are encountered on manned aircraft operating at very high speeds. Very high speeds are considered to be from Mach 2 or 1300 mph to speeds of the order of Mach 38 or 25,000 mph, which is the velocity for escape from the earth. Mach 2 is considered a logical starting point since it represents the approximate upper limit of present day military aircraft. Manned aircraft will continue to be developed for flight at very high speed and high altitudes and the experiences gained will serve as stepping stones to eventual manned satellites and space vehicles. The major problems to be solved relate to aerodynamic heating, stability and control, and human effects. This paper received the 1958 Wright Brothers Medal.

This paper discusses the findings for [Interior] Configuration Options, Habitability and Architectural Aspects of a first human spacecraft to Mars. In 2003 the space architecture office LIQUIFER was invited by the European Space Agency’s (ESA) AURORA program committee to consult the scientists and engineers from the European Space and Technology Center (ESTEC) and other European industrial communities with developing the first human mission to Mars, which will take place in 2030, regarding the architectural issues of crewed habitats. The task was to develop an interior configuration for a Transfer Vehicle (TV) to Mars, especially a Transfer Habitation Module (THM) and a Surface Habitat (SHM) on Mars. The total travel time Earth - Mars and back for a crew of six amounts to approximately 900 days. After a 200-day-flight three crewmembers will land on Mars in the Mars Excursion Vehicle (MEV) and will live and work in the SHM for 30 days.

To enable the tests required for development work to be performed with maximum efficiency, the Zwick Roell Group (ZwickRoell) – a global supplier of materials testing machines based out of Ulm, Germany – developed a materials testing machine that can be equipped with both a temperature chamber and a high-temperature furnace.

In a 2-year program sponsored by SJAC, an aqueous electroplating process using alkaline Zn-Ni with trivalent chromium post treatment is under evaluation for high strength steel for aircraft application as an alternative to cadmium. Commercial Zn-15%Ni rack/barrel plating solutions are basis for plating aircraft parts or fasteners. Brightener was reduced from the original formula to form porous plating that enables bake-out of hydrogen to avoid hydrogen embrittlement condition. Properties of the deposit, such as appearance, adhesion, un-scribed corrosion resistance, and galvanic corrosion resistance in contact with Al alloy, were evaluated. Coefficient of friction was compared with Cd plating by torque-tension measurements. Evaluation of the plating for scribed corrosion resistance, primer adhesion, etc. will continue in FY2007.

This paper describes the testing of a waste management system designed and fabricated for use in a space vehicle. The system provides for the collection and inactivation of urine, feces, emergency diarrheal disorders, vomitus, and debris; the volumetric determination of each micturition; and onboard storage of the inactivated wastes within the waste management system compartment. The zero-gravity test program conducted in a KC-135 aircraft provided the primary verification of the performance of the waste collection and urine volume determination functions prior to actual space flight. The test hardware simulated the actual system to a high degree of fidelity with respect to operational characteristics of the airflow required in collection, mechanical functions and system pressure differentials, in order to minimize simulation errors.

For human beings who have been reared on the earth with its 1 G gravitational field, the condition of weightlessness is a world with which we are unfamiliar. Even if the layout and equipment configuration of a spacecraft designed to compensate for operation under Zero-G conditions, there are some things which are not effective under actual weightless conditions. In the design of a manned spacecraft, it is necessary to accumulate design data on human performance in a weightless condition, then to undertake design evaluations and verification under weightless conditions. In this paper, testing for the purpose of evaluating the effectiveness of Zero-G simulation using neutral buoyancy, conducted first of all in Japan, and recommendations on the equipment and Facilities required to conduct such simulations, are described.

Zero trust (ZT) is an emerging initiative that focuses on securely providing access to resources based on defined policies. The core tenet of ZT is “never trust, always verify”, meaning that even within trusted zones of operation, resource access must be explicitly granted. ZT has proven effective in improving the security posture in domains such as information technology infrastructure; however, additional research and development is needed to define and apply zero trust principles to cyber-physical system domains. To work toward this objective, we have identified an initial set of ZT architectural patterns targeted specifically at cyber-physical systems. We created ZT architecture patterns in the Architecture Analysis and Design Language (AADL), a modeling language that enables engineers to describe the key elements of embedded system architectures using a well-defined semantics.

Manned spacecraft life suport systems must operate in a zero gravity environment. Lack of the “pull” of gravity affects heat and mass transfer, fluid transport, phase change, and chemical and electrochemical processes. This paper covers new concepts necessary for humidity control, evaporative coolers, distillation units, and similar equipment required for spacecraft life support. Specific applications used on the Space Shuttle and in development for advanced regenerative systems are discussed, including how they work, how they are tested on earth, and how much, if at all, the weightless environment penalizes the designs.

Spacecraft life support equipment is often challenged with two phase flow, where liquid and gas exist together. In the zero gravity environment of an orbiting spacecraft, the behavior of a liquid/gas interface is dominated by forces not usually observed in one “G” due to the overwhelming effects of gravity. The normal perceptions no longer apply. Water does not run down hill and bubbles do not rise to the surface. Surface energy, capillary forces, wetting characteristics and momentum effects predominate. Techniques and equipment have been developed to separate the liquid/gas mixture into its constituent parts with various levels of efficiency and power consumption.